When you select a Bank, its number appears on the display. When you deselect a Bank, its number disappears from the display. When you press Hto stop scanning, only the Bank of the current channel appears. Frequency Indicator — 7-digits plus decimal indicate the frequency being received by the scanner. Mode Indicators — Only the active mode s are displayed during operation. Also use to access a channel directly with H.
Only the selected bank indicator s appear on the display. Note:You cannot deactivate all 10 banks at the same time. Add page 8 to Favourites. HOLDappears on the display. After you stop the scanner, press Hagain to resume scanning or searching. Press Nto toggle the Preprogrammed Search Band. SRCHappears on the display. Press Sto start scanning all programmed channels that are not locked out. SCANmoves across the display during scanning. In this mode, when the scanner monitors an active frequency, searching or scanning will not resume until transmission stops for 2 seconds.
WXappears on the display in Weather Mode. Press Lto turn the display light ON for 15 seconds. Press Lagain to manually turn the light OFF. Press and hold until appears on the display.
This disables the keypad and prevents any accidental key entries. To enable the keypad, press and hold until disappears from the display. Add page 9 to Favourites. If you make an entry error, press. Press Eto store a displayed frequency into any displayed channel. To unlock a channel, press Oagain. PRIappears on the display.
This feature is not active in the Air Band. Add page 10 to Favourites. When fully charged, this Battery Pack will supply up to 12 hours of dependable use. Page 21 a. Place the point of a ball point pen into the small hole of the Memo Pad plastic cover, and lift it off. Write the names or other identifying remarks in each channel block on the Memo Pad. When the Weather Search finds an active channel in your area, the scanner stops at that frequency. To stay at that frequency, press Weather Search, press It is possible that you may be able to hear more than one Weather broadcast in your area.
Page Searching 1 frequency step. See the table on page for the step size for each Band. A scanner will normally stop on any transmission it receives. This means the SportCat will stop on Data signals and unmodulated transmissions.
You can skip these frequencies during Search. The scanner may stop at certain frequencies during Search that you do not want to hear. You can program up to Skip Frequencies into the SportCat. When the scanner stops at one of these frequencies during Search, press.
Page Care And Maintenance 4. Carefully unplug the Battery Back and lift it out of the case You may need to exert a slight pressure toward the top of the scanner as you slide the Battery Pack out of the case. Carefully plug in the new Battery Pack, observing the proper polarity.
Do not use excessive amounts of water. Repairs Do not attempt any repair. The scanner contains no serviceable parts. Contact the Uniden Customer Service Center or take it to a qualified repair technician. Birdies are internally generated signals inherent in the electronics of the scanner. Use the Search Skip feature to skip the unwanted frequencies. Page Troubleshooting If you still cannot get satisfactory results and want additional information, or to return the unit for service, please call or write the Uniden Parts and Service Division.
The address and phone number are listed in the Warranty at the end of this manual. Be sure to use only the supplied earphone, or a stereo headset of the proper impedance Page One Year Limited Warranty E used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or F installed or programmed by anyone other than as detailed by the Operating Guide for this product.
All rights reserved. This manual is also suitable for: Scy Sportcat twin turbo sports scanner Sportcat sc Bearcat sportcat sc Print page 1 Print document 35 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Sign up! Release Notes. To enter registration key: open program, click on "write to scanner", click on "setup" at top and then "registration".
A box will open so that you can enter the number that was emailed to you. If you are upgrading from a previous version, you do not need to uninstall the old version. All existing data and your registration information will be preserved.
DFR7 Redlight Database. Download firmware to your PC 2. Unzip the file which will produce 2 firmware files 3. Transfer files to a clean, formatted SD card.
0コメント